Chinese translation for "friction conditions"
|
- 摩擦条件
Related Translations:
- Example Sentences:
| 1. | Design of tire fault observer based on estimation of tire road friction conditions
路面磨擦状况估计的轮胎故障观测器设计 | | 2. | The effect of the friction condition including the load and the sliding velocity on the wear of the composites was studied under water - lubricated condition and dry condition
本文还讨论了在水润滑与干摩擦条件下，载荷与滑动速率对纳米复合材料摩擦磨损性能的影响。 | | 3. | Squeeze flow between two parallel disks is considered for small gaps for rigid - plastic material with partial wall slip . firstly , the coulombic friction condition is discussed , and a new pressure distribution is obtained
首先对现有的库仑摩擦条件下的压力规律做了进一步的研究，找到了一种更合理的圆盘上的压力分布规律。 | | 4. | Based on the tribological principle and the theory of contact mechanics , it is feasible to adopt curvature - changing structure in the rock - bit journal bearing system . the structure and coupling relationship of curvature - changing journal bearing under the condition without friction have been analyzed and three kinds of sub - form structure configurations , namely , the pseudo - curvature - changing structure , the conformable curvature - changing structure , and the clearance curvature - changing structure , been differentiated according to the contacting features . the shape optimization and pre - running - in regulations of the contact surface of curvature - changing journal bearing under friction condition have been established . the results of rock bit journal bearing test indicate that the tribological behavior of the bearing can be effectively improved by curvature change based on both designing and pre - running - in
基于摩擦学原理和接触力学理论,提出了可在牙轮钻头滑动轴承中采用变曲率结构.在不考虑摩擦的情况下，就结构设计和配合关系等问题进行了分析讨论，划分了准变曲率、吻合变曲率以及间隙变曲率等3种结构形式；针对考虑摩擦时的变曲率结构，提出了接触形状优化和预磨合的实施方案.钻头轴承试验结果表明，无论是预设计变曲率还是预磨合变曲率，都能改善轴承摩擦副的摩擦学特性，因而值得进一步研究和推广 | | 5. | And also , the wear resistance at ambient temperature and of za27 alloyed with mn when lightly loaded is desirable but becomes worse at high temperature . the wear mechanism of the one mixed with both adhesive and abrasive wear under sliding friction conditions ( at high temperature )
Si的加入量为1 - 3时， za27合金的磨损量最少，高温摩擦性能最好；加入mn后， za27合金在低温轻载下耐磨性能较好，高温耐磨性能不理想；在滑动摩擦条件下(高温)的磨损以粘着磨损和磨料磨损两种方式共同存在。 | | 6. | But when heavyly loaded , the former is far better than the latter . the wear resistance of za27 alloyed with mn is no obviously better than that of common za27 alloy . under the sliding friction conditions , the wear resistance at high temperature of za27 is improved by alloyed si and reaches the highest level when the content of si is 1 - 3wt . %
裂纹主要始于脆性相si相和mn相，裂纹沿晶界扩展；在滑动摩擦条件下(常温) ，含si的za27合金在载重较小时，耐磨性与普通za合金相比没有明显提高，但在载荷较大的情况下，其耐磨性远高于普通za27合金材料；加mn的za27合金与常规za27合金相比，耐磨性没有明显提高；在滑动摩擦条件下， si的加入提高了za27合金的高温摩擦性能。 | | 7. | Moreover , based on the assumption that the slip velocity at the disks increases linearly with the radius up to the rim slip velocity , another pressure distribution is derived by introducing a appropriate velocity field . then these different results by the different friction conditions and technique are compared . 2
同时，在圆盘边缘处滑移速度一定，介质的滑移速度随着半径线性变化的假设下，引入合理的速度场，得到了另一种圆盘上的压力分布规律，并对不同的摩擦条件及用不同方法计算得到的结果进行了对比。 |
- Similar Words：
- "friction coefficient" Chinese translation, "friction coefficient of masonry" Chinese translation, "friction compensated" Chinese translation, "friction compensation" Chinese translation, "friction compound" Chinese translation, "friction cone" Chinese translation, "friction cone clutch" Chinese translation, "friction cone drive" Chinese translation, "friction conglomerate" Chinese translation, "friction constant" Chinese translation
|
|
|
